V1.4.0 Additional Features:- New add-ons available: DeEsser, Multiband Compressors (MultiBD3/MultiBD4), Dynamic EQ (DynEQ4)
- Ganging
- Per-scene recall filters
- USB Scene and Library archiving
- Copy Paste Reset of Scenes and Per-scene recall filters
- IO Page socket control
- Sync Mode for SQ-MixPad connection
- MIDI NRPN control of Levels, Panning/Balance, Mutes, Assignments, SoftKeys
- Mono matrix option
- Preamp on surface option
- Processing screen follows surface option
- PEQ band follows screen option
- Name/Colour options in channel library
- HPF option in PEQ library
- New soft control additions – MIDI program changes, note on/off, Listen Level
- SQ-MixPad additions – Offline mode, follow SQ channel/mix options, PAFL setup, channel routing screen
- Support for DX32 modular expander added
- Global recall filters re-organised and extended
- SQ-Drive performance metering
- RTA peak band indication in GEQ Fader Flip
- Socket number displays on channel LCD display
- Channel and strip numbers added to strip assign
- Touch scrolling added to all on-screen lists
Improvements:- ID-1201: Channel ms delay control improved
- ID-1227: Compressor parallel path Dry/Wet control improved
- ID-819: Channel mute time when engaging/disengaging PAD reduced
- ID-620: Fader calibration process no longer requires rebooting
Issues fixed:- ID-720: Removed persistent metering when dSnake unit is disconnected
- ID-1008: Mixer shutdown gracefully closes SQ-Drive recording
- ID-1149: Reset Mix Settings button blocked correctly using user permissions
- ID-1044: Input patch filtered when preamp recall blocked
- ID-1266: SQ-Drive seek bar appears correctly on first launch of screen
- ID-1276: SQ-Drive recording to maximum length no longer lists two recordings in playback
- ID-565: Stereo insert left disconnects correctly when right send is repatched elsewhere
- ID-1390: Corrected issue with incorrect output patching when switching mix stereo/mono
- ID-894: Insert LED correctly displays status on scene recall
- ID-807: FX Library items now contain Dry/Wet levels when stored as insert
- ID-563: Insert point In/Out status persists when creating or editing
- ID-1307: Correction to stereo flag when sending mix channels to a ME system
- ID-364: Preamp surface control does not affect trim when Mix Ext In has no preamp available
- ID-1339: AR84 Tie Line patching now persistent after power cycle
- ID-1271: Routing screen now displays from LHS on opening
- ID-1287: Fixed inconsistency in AFL/PFL on LR when switching output AFL setting
Known issues – SQ-Drive:Loss of power or unplugging a device during multi-track or stereo record may result in the current recording being lost.
Known issues – Firmware update whilst connected via USB-B:When connected via USB-B, SQ may not install firmware correctly from a USB device. Disconnect the USB cable before attempting an update.
Known issues – Firmware update does not install on both images:The SQ has a main image and back-up image for stability and redundancy. If an update has been carried out, and the SQ boots into an older firmware, the update should be carried out again to ensure both images are running the same version.
Known issues – Audio not passing when attempting to load an unavailable upgrade:When loading a show which uses upgrades not available in the installed firmware, a default processing unit will be loaded, but audio will not pass until the processing has been switched out. This can happen when a show saved on newer firmware is loaded into an SQ running older firmware.
Known issues – Incorrect sync with MixPad when Mixer Config is changed:Adjusting the Mixer Config on the desk will cause issues in the SQ-MixPad I/O Patch screen until the app has been disconnected and reconnected. For this reason, SQ-MixPad should only be connected after Mixer Config settings have been applied at the desk.
