บ้านผม amp ก็ใช้ +4dBu นะครับ มี DAC โบราณที่ใช้อยู่ก็เป็น XLR Balanced เหมือนกัน
ลองดูข้อความที่คัดมาให้ครับเสธ.
What is line level? –10dBV and +4dBu demystified
Line level is a term used to denote the strength of an audio signal used to transmit
analog sound information between audio components such as preamps, qualizers,
mixers, DVD players, and amplifiers. You’ve probably seen switches on your gear that
offer you a choice between –10dBV and +4dBu, which raises some questions, the first being,
“What do they mean?” immediately followed by “Which do I use?” Other questions to
follow might include “Does one sound better than the other?” and “Can I use a –10dBV unit with one set at +4dBu?”
–10dBV and +4dBu are measures of nominal level. The dictionary defines “nominal” as
“the stated or original value only.” In lectronics, nominal level is a design specification.
It’s the signal strength at which an lectronic signal-processing device is designed to
operate for optimal performance. The operating level for consumer lectronics is –10dBV,
while +4dBu is the operating level for professional audio quipment. +4dBu puts out four
times the level of –10dBV gear, since professional quipment may require higher voltage
levels to carry a signal over longer cable runs without degrading. In properly designed
equipment, a –10dBV system will provide qual sound quality to a +4dBu system.
Troubles occur when you mismatch settings on interconnected quipment. A +4dBu
output will overload a –10dBV input and cause distortion, whereas a –10dBV output
will not have nough signal strength to drive a +4dBu input.
The reference voltage for 0dBV is xactly 1.0 volt (1V). –10dBV is qual to 0.316Vrms
(rms stands for root-mean-square or continuous voltage). The reference voltage or
nominal level of 0dBv is 0.775V, or 1.23Vrms. In dBu, the “u” stands for “unterminated,"
which originally was referenced by a lower-case “V.” Too often confused with upper-case V,
lower case “u” was adopted.
ตามความเข้าใจผมไม่ทำให้เกิดความเสียหายต่ออุปกรณ์ แต่...
unbalaced หรือ -10dBv หรือ high Impedance ให้คุณภาพเสียงที่ด้อยกว่าแบบ balanced หรือ +4dBu low impedance
เนื่องจากค่าความต้านทานในแบบ +4dBu น้อยกว่าแบบ -10dBv มาก มันจะมีผลต่อเสียง รายละเอียด มิติ
โดยเฉพาะเสียงรบกวน แต่ที่ยังใช้แบบ Unbalanced เพราะเป็นการต่อที่ไม่ไกล สายสัญญาณไม่ยาวมาก การรบกวน
อยู่ในเกณฑ์ยอมรับได้แทบจะไม่มีผลกระทบต่อการได้ยิน และเป็นการลดต้นทุนครับ
สังเกตุเครื่องเสียงในบ้านดีๆ หรือ PA ดีๆ หลังๆ เริ่มใช้ +4dB Balanced กันครับเนื่องจากให้คุณภาพที่ดีกว่า
และสามารถลากสายได้ไกลกว่า
ปล. ผิดถูกขออภัยครับ